新闻中心
|
木工雕刻机的台面如何清洗长期使用雕刻机的人都知道,雕刻机台面使用时间长了是很容易导致毛刺不平的。这样的情况下机器进行雕刻的话就很容易导致板不平,雕刻的时候容易出现花刀,图案毛刺多,且很容易直接把板雕错,所以适当的清洗台面是非常有必要的。那么木工雕刻机的台面如何清洗呢?下面就让小编来告诉大家两个小方法。 先做好台面大小的矩形洗底路径图,深度不要太深。关键的一点是对刀的时候要在台面上找到Z低点。就是手动多走一会,看哪里洗不到,在Z低点定Z原点。重叠率要高,这样洗出来的台面才更平整。 方法一:台面常用PVC板做底,在软件里画个和台面一样大小的距形,然后2D洗底,和平常洗双色板一样的。 换一个粗一点的麻花刀,洗起来就快了。下刀深度要根据情况而定,基本上是深底到没有凹的地方为佳。洗完后打扫一下就可以了。 方法二:用专用的清底刀。 找到机器台面的Z低点然后把刀下0.5-1mm深,然后启动主轴手动操作来回跑可以了,注意:根据台面材质的不同选择不同的进给速度。 木工雕刻机清洗的方法很简单并不麻烦,且保养好机器能够延长机器的使用寿命,所以定期清洗台面是非常有必要的,不要偷懒哦! People who have used the engraving machine for a long time know that the use of the engraving machine countertop for a long time can easily lead to uneven burrs.In this case, if the machine is engraving, it is easy to cause the board to be uneven. When carving, it is easy to have flower knives, many burrs in the pattern, and it is easy to directly carve the board wrong, so it is very necessary to properly clean the countertop.So how to clean the countertop of the woodworking engraving machine?Let Xiaobian tell you two small methods. First make a rectangular bottoming path map of the size of the countertop, and the depth should not be too deep.The key point is to find the Z low point on the countertop when facing the knife.Just walk manually for a while, see where you can't wash it, and set the origin of Z at the low point of Z.The overlap rate should be high, so that the washed countertop is smoother. Method 1: PVC board is commonly used as the bottom of the countertop. Draw a pitch shape of the same size as the countertop in the software, and then wash the bottom in 2D, the same as the usual two-color board. Change to a thicker twist knife and it will wash quickly.The depth of the knife should be determined according to the situation, basically it is better to have a deep bottom to a place where there is no concave.Just clean it up after washing. Method two: Use a special bottom-clearing knife. Find the Z-low point of the machine countertop and put the knife 0.5-1mm deep, then start the spindle to run back and forth manually. Note: Choose different feed speeds according to the different table materials. The cleaning method of woodworking engraving machine is very simple and not troublesome, and maintaining the machine well can extend the service life of the machine, so it is very necessary to clean the countertops regularly. Don't be lazy! |